|
- 品牌：德國KAYSEN
- 貨號：KS8538179
- 發布日期： 2019-10-12
- 更新日期： 2024-10-21
| 外型尺寸 | |
| 貨號 | KS8538179 |
| 品牌 | KAYSEN |
| 用途 | 抽水、化工、制藥、石油、冶金、染料、冶煉、電力、電鍍、農藥、造紙、食品、紡織等行業酸洗工藝、制酸制堿、噴漆工藝、有色金屬冶煉中的電解液輸送、離子膜項目中的氯水輸送、廢水處理、電鍍、農藥領域。 |
| 型號 | KAYSEN |
| 工作壓差 | 0 |
| 壓力環境 | 常壓 |
| 介質溫度 | 250℃ |
| 驅動方式 | 電動 |
| 適用介質 | 水 |
立式化工泵-化工泵-KAYSEN泵業
GERMANY KAYSEN PUMP CO .,LTD
立式化工離心泵，采用IH型離心泵之性能參數，在一般立式泵的基礎上簡化結構設計而成。根據使用溫度、介質等不同在ISG型基礎上派生出IHG型不銹鋼化工泵。該系列產品的特點為結構緊湊，零配件種類少，使用和維修方便。
主要特點：
●泵為立式結構，進出口口徑相同，且位于同一中心線上，可象閥門一樣安裝于管路之中，外形緊湊，占地面積小，如加上電機防護罩則可置于戶外使用。
●葉輪直接安裝在電機的加長軸上，軸向尺寸短。
●軸封采用機械密封，根據介質可有不同的材質配置，能根據實際情況有效地延長機械密封的使用壽命。
●安裝檢修方便，無需拆動管道路系統，只要卸下泵聯體座螺母即可抽出全部轉子部件。
●可根據流量使用要求，采用并聯運行方式。
●可根據管路布置的要求采用泵的豎式和橫式安裝。
主要應用：
供輸送不含固體顆粒（或者含微量細小顆粒，具體請咨詢技術人員），具有一定腐蝕性，粘度類似于水的液體，被輸送介質溫度為-50℃~+150℃。廣泛用于石油、化工、冶金、電力、造紙、煙氣脫硫、除塵、食品制藥和合成纖維等部門.
化工泵使用注意事項：
化工泵可根據不同的使用條件安裝不同形式的機械密封，(如內裝單端面平衡型和非平衡型，雙端面平衡型及非平衡型，外裝式機械密封等)。根據所選用密封型式的不同，其使用方法和注意事項也有所不同，具體情況請參閱機械密封安裝使用說明書、GB3215-82“煉廠、化工及石油化工流程用離心泵通用技術條件"，下面佰諾泵閥僅提幾點一般應注意的事項。
●由于機械密封一般適用在清潔的，無懸浮顆粒的介質中使用，因此，對新安裝的管路系統和儲液灌，應認真沖洗干凈，嚴防固體雜質進入機械密封端面而使密封失效。
●在易結晶的介質中，使用機械密封應注意經常沖洗。停車后重新起動前，要將機械密封上的結晶清洗干凈。
●拆卸機械密封應仔細，不許用手錘，鐵器等敲擊，以免破壞動、靜環密封面。
●如果有污垢拆不下來時，應設法清除污垢，沖洗干凈后再進行拆卸，以免損壞密封元件。
●安裝機械密封前，應檢查所有密封元件是否有失效或損壞，如有則應重新修復或更換。
●應嚴格檢查動環與靜環的相對磨擦密封面，不允許有任何細微的劃痕、碰傷等缺陷。所有另部件，包括泵體，葉輪，密封腔等在裝配前均應沖洗干凈，尤其是動、靜環端面，要用清潔，柔軟的布或棉紗認真擦拭干凈，然后涂上一層清潔的油脂或機油。
●裝配中要注意消除偏差，緊固螺釘時，要均勻擰緊，避免發生偏斜，使密封失效。
●正確調整彈簧的壓縮量，泵安裝好以后，以手扳動轉子時，應感覺到密封彈簧既有一定的壓縮量，而又能輕快、靈活地轉動沒有咬緊的感覺。如感覺太緊或盤不動，則應適當調松一些。
●IH化工泵對有外部沖洗的機械密封，起動前應先開啟沖洗波，使密封腔內充滿密封液。停車時，先停泵，后關密封沖洗液。
Corrosion resistant centrifugal pump
Vertical chemical pump
VChemical centrifugal pump
The imported vertical chemical centrifugal pump adopts the performance parameters of the IH centrifugal pump and is designed on the basis of the general vertical pump. IHG type stainless steel chemical pump is derived on the basis of ISG type according to the use temperature and medium. The series features compact structure, few spare parts, and easy to use and maintain.
main feature:
●The pump is of vertical structure, the inlet and outlet are the same diameter, and they are located on the same center line. They can be installed in the pipeline like a valve. The shape is compact and the footprint is small. If the motor protection cover is added, it can be placed outdoors. .
●The impeller is directly mounted on the extension shaft of the motor and has a short axial dimension.
●The shaft seal adopts mechanical seal. According to the medium, it can be configured with different materials, which can effectively extend the service life of the mechanical seal according to the actual situation.
●Easy to install and repair, no need to dismantle the pipe road system, just remove the pump joint nut to extract all the rotor parts.
● It can be operated in parallel according to the requirements of flow usage.
● The vertical and horizontal installation of the pump can be used according to the requirements of the pipeline arrangement.
main application:
For transport without solid particles (or containing traces of fine particles, please consult the technical staff), a certain corrosive, viscosity similar to water, the temperature of the medium being transported is -50 ° C ~ +150 ° C. Widely used in petroleum, chemical, metallurgy, electric power, paper, flue gas desulfurization, dust removal, food and pharmaceutical and synthetic fiber sectors.
Precautions for the use of chemical pumps:
The chemical pump can be installed with different types of mechanical seals according to different conditions of use (such as built-in single-end balanced and unbalanced type, double-end balanced and unbalanced type, external mechanical seal, etc.). According to the selected sealing type, the method of use and precautions are also different. For details, please refer to the mechanical seal installation and operation manual, GB3215-82 "General technical conditions for centrifugal pumps for refineries, chemical and petrochemical processes", below 佰The pump valve only mentions a few points that should be noted.
●Since the mechanical seal is generally suitable for use in clean, non-suspended particulate media, the newly installed piping system and liquid storage should be carefully rinsed to prevent solid impurities from entering the mechanical seal end face and causing the seal to fail.
● In a medium that is easy to crystallize, use a mechanical seal and pay attention to frequent flushing. The crystals on the mechanical seal should be cleaned before restarting after parking.
● Disassemble the mechanical seal carefully. Do not hit with a hammer or iron to avoid damaging the dynamic and static ring sealing surfaces.
● If there is dirt removed, try to remove the dirt, rinse it and then disassemble it to avoid damage to the sealing components.
● Before installing the mechanical seal, check all seal components for failure or damage, and if necessary, repair or replace them.
● The relative friction sealing surfaces of the moving ring and the stationary ring should be strictly checked. No slight scratches or bumps are allowed. All other parts, including the pump body, impeller, sealing chamber, etc. should be cleaned before assembly, especially the moving and static ring end faces. Wipe clean with a clean, soft cloth or cotton yarn, then apply a layer of clean grease. Or motor oil.
● Pay attention to eliminate the deviation during assembly. When tightening the screws, tighten them evenly to avoid deflection and invalidize the seal.
● Correctly adjust the compression amount of the spring. After the pump is installed, when the rotor is pulled by hand, the seal spring should be felt to have a certain amount of compression, and it can be lightly and flexibly rotated without the feeling of clenching. If you feel too tight or do not move, you should loosen some of them properly.
● IH chemical pump for mechanical seal with external flushing, the flushing wave should be turned on before starting, so that the sealing chamber is filled with sealing liquid. When parking, stop the pump first, then close the seal flushing fluid.
位于Schw?bischGmünd的凱森Kaysen泵業有限公司是世界*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持世界各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。
凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
