国产午夜亚洲精品理论片,黄色成人传媒片在线播放,亚洲窝窝色影院之寻求快感,久久亚洲Av无码精品午夜麻

噴泉泵-不銹鋼噴泉泵-KAYSEN泵業

GERMANY KAYSEN PUMP CO .,LTD

噴泉專用泵，外殼、過流部件及外部零件材質均采用鑄鐵或者不銹鋼（304、316、316L）制成的，并且該產品還保留了原來噴泉專用泵性能。開泵前，吸入管和泵內必須充滿液體。開泵后，葉輪高速旋轉，其中的液體隨著葉片一起旋轉，在離心力的作用下，飛離葉輪向外射出，射出的液體在泵殼擴散室內速度逐漸變慢，壓力逐漸增加，然后從泵出口，排出管流出。

主要特點：

噴泉專用泵其外殼、過流部件及外部零件材質均采用鑄鐵或者不銹鋼（304、316、316L）制成的，并且該產品還保留了原來噴泉專用泵性能。
●采用鑄鐵或者不銹鋼材料，提高泵的耐腐蝕性。
●葉輪采用專用材料防止葉輪時葉輪松動?！娙獙Ｓ帽?br/>●漏電保護措施：采用定電位接地裝置。
●在原普通泵的基礎上，根據噴泉專用泵的要求，公司經 過多次試驗，在技術上不斷開發，加工材料上不斷改進，使噴泉專用泵可以頻繁起動，完全適合音樂噴泉的使用。
●泵采用不銹鋼濾網護罩，三相四線電纜。
●不銹鋼噴泉泵為自動注水功能。
●該電機為自循環充水式冷卻。

主要應用：
噴泉潛水泵主要用于噴泉供水,水產養殖等場所。廣泛用于低揚程的城市、農田排 灌、噴灌,工業及民用的供、排水系統,丘陵、山區引水,以及低洼地排除積水。

噴泉泵故障排除法：
       1.啟動時水泵不轉　原因：填料太緊或葉輪與泵體之間被雜物卡住而堵塞；泵軸、軸承、泄漏環銹住；泵軸嚴重彎曲。排除方法：放松填料，疏通引水槽：拆開泵體清除雜物或銹；校正彎曲的軸或換新的泵軸。
　　2.啟動后水泵不出水　原因：泵內有空氣或進水管積氣；底閥關閉不嚴灌水不滿、真空泵填料嚴重漏氣；閘閥或拍門關閉不嚴。排除方法：清除雜物，更換已損壞的橡皮墊，改變閥片方向；壓緊或更換新的填料，關閉閘閥或拍門；加大灌水量，直到放氣螺塞處不冒氣泡；更換有裂紋的管水；降低揚程，將水泵的管口壓入水下0.5米。
　　3.流量不足　原因：水泵實際揚程超過允許揚程；轉速不配套或皮帶打滑、轉速偏低；軸流泵葉片安裝角太小；吸程過高；底閥、管路及葉輪局部堵塞或葉輪缺損；出水管漏水嚴重。排除方法：降低揚程，恢復額定轉速，清除皮帶污垢并調好皮帶緊度；調好葉片角，降低水泵安裝位置；擰緊壓蓋、密封水泵漏水處，壓緊填料或更換填料；清除堵塞物、更換葉輪；更換泄漏環，堵塞漏水處。
　　4.流量由大變小　原因：濾網或喇叭口逐漸被雜物堵塞；動水位降低、進水管淹沒水深不夠。排除方法：清除雜物，加大底閥入水深度。
　　5.運行中出水中斷　原因：管路或進水處有雜物堵塞；填料磨損、松動、水封管堵塞；葉輪被打壞或松脫；動水位劇降。排除方法：清除堵塞物，更換填料、疏通引水管溝槽，正確安裝水封環；緊固或更換葉輪；降低水泵安裝位置，或待水位上升后再開機。
　　6.功率消耗太大　原因：轉速過高；泵軸彎曲；葉片繞有雜物；揚程過高。排除方法：調整合適的轉速；校正泵軸；清除雜物；設法降低揚程。

噴泉泵日常維護：
(1)檢查并處理易于松動的螺栓或螺母。如拍門、螺栓、軸銷、銷釘?shù)?，雙吸離心泵軸封裝置填料的松緊程度，空氣壓縮機閥片等。
(2)油、水、氣管路接頭，閥門滲漏處理。
(3)電動機碳刷、滑環、絕緣等的檢查處理。
(4)檢查攔污柵前有無阻水雜物。
(5)保持電動機干燥，檢查電動機絕緣。
(6)檢修閘門吊點是否牢固，門側有無卡阻物、銹蝕及磨損情況。
(7)閘門啟閉設備維護。
(8)吊車維護。
(9)機組設備清潔。

The special pump for the fountain, the outer casing, the over-current parts and the external parts are made of cast iron or stainless steel (304, 316, 316L), and the product retains the original pump-specific pump performance. The suction tube and pump must be filled with liquid before the pump is turned on. After the pump is turned on, the impeller rotates at a high speed, and the liquid rotates with the blade. Under the action of the centrifugal force, it flies outward from the impeller, and the liquid that is ejected in the pump chamber diffuses slowly, the pressure gradually increases, and then the pump At the exit, the discharge pipe flows out.

main feature:

The fountain pump has its outer casing, over-current parts and external parts made of cast iron or stainless steel (304, 316, 316L), and the product retains the original pump-specific pump performance.

●Use cast iron or stainless steel to improve the corrosion resistance of the pump.

●The impeller uses special materials to prevent the impeller from loosening when the impeller is used. Fountain special pump

● Leakage protection measures: Use a constant potential grounding device.

● On the basis of the original ordinary pump, according to the requirements of the special pump for the fountain, the company has undergone many tests and continuously developed in technology, and the processing materials have been continuously improved, so that the special pump for the fountain can be started frequently, which is completely suitable for the use of the musical fountain.

●The pump adopts stainless steel strainer shield and three-phase four-wire cable.

● Stainless steel fountain pump is automatic water injection function.

● The motor is self-circulating and water-cooled.

main application:

The fountain submersible pump is mainly used in fountain water supply, aquaculture and other places. It is widely used in low-lift cities, farmland irrigation, sprinkler irrigation, industrial and civil supply and drainage systems, water diversion in hills and mountains, and low-lying water.

Fountain pump troubleshooting method:

       1. The pump does not turn when starting. Cause: The packing is too tight or the impeller and the pump body are stuck by the debris; the pump shaft, the bearing and the leakage ring are rusted; the pump shaft is severely bent. Remedy: Dissipate the packing and clear the drain: Disassemble the pump to remove debris or rust; correct the bent shaft or replace the pump shaft.

2. The pump does not produce water after starting. Cause: There is air in the pump or water in the inlet pipe; the bottom valve is not tightly filled with water, the vacuum pump packing is seriously leaked; the gate valve or the door is not closed. Remedy: remove debris, replace the damaged rubber mat, change the direction of the valve; press or replace the new filler, close the gate valve or flap the door; increase the amount of water until the venting plug does not bubble; replace Cracked pipe water; reduce the lift and press the nozzle of the pump into the water 0.5 m.

3. Insufficient flow: The actual lift of the pump exceeds the allowable lift; the speed is not matched or the belt slips and the speed is low; the installation angle of the axial pump blade is too small; the suction stroke is too high; the bottom valve, pipeline and impeller are partially blocked or impeller defect The outlet pipe is leaking seriously. Remedy: reduce the lift, restore the rated speed, remove the belt dirt and adjust the belt tightness; adjust the blade angle to reduce the pump installation position; tighten the gland, seal the water pump leakage, press the packing or replace the packing; remove the blockage, Replace the impeller; replace the leak ring and block the leak.

4. The flow rate is changed from large to small. Cause: The filter or bell mouth is gradually blocked by debris; the moving water level is lowered, and the water inlet is submerged. Remedy: Remove debris and increase the depth of the bottom valve.

5. Intermittent water outage during operation Cause: There is debris in the pipeline or water inlet; the packing is worn, loose, and the water sealing tube is blocked; the impeller is broken or loose; the water level drops sharply. Remedy: remove the blockage, replace the packing, clear the groove of the water pipe, install the water seal ring correctly; tighten or replace the impeller; reduce the installation position of the water pump, or turn the water on after the water level rises.

6. Power consumption is too large Cause: The speed is too high; the pump shaft is bent; the blade is surrounded by debris; the lift is too high. Remedy: Adjust the appropriate speed; calibrate the pump shaft; remove debris; try to lower the lift.

Fountain pump daily maintenance:

(1) Inspect and handle bolts or nuts that are easy to loosen. Such as shooting doors, bolts, axle pins, pins, etc., the double-suction centrifugal pump shaft sealing device packing tightness, air compressor valve and so on.

(2) oil, water, gas pipeline joints, valve leakage treatment.

(3) Inspection and treatment of motor carbon brushes, slip rings, insulation, etc.

(4) Check for water-blocking debris before the trash rack.

(5) Keep the motor dry and check the motor insulation.

(6) Check whether the lifting point of the gate is firm, and there is no jam, rust and wear on the door side.

(7) Maintenance of gate opening and closing equipment.

(8) Crane maintenance.

(9) The unit equipment is clean.

       位于Schw?bischGmünd的凱森Kaysen泵業有限公司是世界*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持世界各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。

        凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。

        The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
          Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.