国产午夜亚洲精品理论片,黄色成人传媒片在线播放,亚洲窝窝色影院之寻求快感,久久亚洲Av无码精品午夜麻

進口井用潛水泵-深井泵-德國KAYSEN泵業

GERMANY KAYSEN PUMP CO .,LTD

德國凱森進口井用潛水泵是深井提水的重要設備.使用時整個機組潛入水中工作.把地下水提取到地表,是生活用水.礦山搶險.工業冷卻.農田灌溉.海水提升.輪船調載.還可用于噴泉景觀.熱水潛水泵用于溫泉洗浴.居民小區利用地?zé)岵膳瘯r可作為地?zé)嵫h(huán)泵等,用途十分廣泛. 該產品是地?zé)衢_發利用工程的重要提水設備，耐熱、防腐、抗老化，使用溫度120℃，通過國家部級鑒定。潛水電機外殼采用不銹鋼及錫青銅材料。

主要特點：

●單級揚程高.單級泵殼高度矮.縮短了整機的高度增加了運行的穩定性。
●泵軸直徑遠大于國標直徑.為提取超級深井的地下水源增加了安全系數。
●鑄件采用HT200(普通鑄件在HT150以下)超級深井泵殼采用球墨鑄鐵.鑄鋼.不銹鋼來提高泵殼的承壓系數。
●逆止閥采用獨特的設計方式.從根本上避免了超深井潛水泵.因停泵時回水水錘沖擊力過大而造成的閥體斷裂機組掉井的弊端。
●軸向力小增加了電機的使用壽命。

主要優點：
●具有結構緊湊
●體積小
●安裝、使用維護方便
●運輸安全可靠
●節約能源等優點

主要應用：
●消防用抽水設備
●供水干管
●農業灌溉、礦場
●地?zé)崴?br /> ●石化行業、具有腐蝕性和研磨性液體的化學系統
●鋼廠的熱處理設施

井用潛水泵的維護和注意事項：
為了保證井用潛水泵裝置的正常工作，減小故障率，延長使用壽命，平時必須加強對深井潛水泵的維修維護，定期對潛水泵及其控制系統進行全面的維護保養，每年至少做一次全面的預防性檢修。
井用潛水泵使用中需要注意的維護與保養方法如下：
1、深井泵裝置的使用環境應經常保持干燥。立式電動機表面應保持清潔，進風口不應受塵土、纖維等雜物的阻礙，保證風道暢通無阻。電動機周圍不應放置熱源，也盡量不要在戶外直射陽光下使用，以免運行中過熱造成損壞。
2、深井泵裝置運行時，應經常注意有關儀表的讀數，并定時記錄水泵運行中的有關參數（如電動機的電壓、
3、運行中如發現有任何不正常的響聲，應立即停車進行檢查。如發現電動機的防逆轉裝置失去作用時，必須進行檢修，清楚污物，使其能良好地工作。
4、電動機控制裝置的過電流保護或短路保護連續發生動作時，應檢查故障是來自電動機過載還是保護裝置定制太低。如果是保護裝置的整定值太低，應調整保護裝置的整定值至合理的數值；如果是因電動機過載造成，應及時檢查電動機過載的原因，消除過載故障才可重新投入運行。
5、每次運行中因故停車時，應注意檢查電動機油標的油位，如發現油位低于油標的一半時，應及時補充新油，以保證電動機角接觸球軸承的可靠潤滑。

Kaysen well submersible pump is an important equipment for deep well water pumping. When using, the whole unit is submerged into the water. The groundwater is extracted to the surface, which is domestic water. Mine rescue. Industrial cooling. Farmland irrigation. Seawater lifting. Ship loading. Can also be used Fountain landscape. Hot water submersible pump is used for hot spring bath. Residential area can be used as geothermal circulation pump when using geothermal heating. It is widely used. It is an important water-lifting equipment for geothermal development and utilization project, heat-resistant, anti-corrosion and anti-aging. The temperature is 120 ° C and passed the national level appraisal. The submersible motor housing is made of stainless steel and tin bronze.

main feature:

● Single stage lift height. Single stage pump casing height is short. Shortening the height of the whole machine increases the stability of operation.

● The diameter of the pump shaft is much larger than the diameter of the national standard. It increases the safety factor for extracting the groundwater source of the super deep well.

●The castings are made of HT200 (common castings below HT150). Super deep well pump casings are made of ductile iron, cast steel and stainless steel to increase the pressure coefficient of the pump casing.

●The check valve adopts a unique design method. It fundamentally avoids the disadvantages of the ultra-deep well submersible pump. The valve body breakage unit is lost due to the excessive impact force of the return water hammer when the pump is stopped.

● The small axial force increases the service life of the motor.

The main advantage:

● has a compact structure

● small size

● Easy to install, use and maintain

● Transportation is safe and reliable

●Energy saving and other advantages

main application:

●Fire pumping equipment

●Water supply main pipe

●Agricultural irrigation, mines

●Geothermal well

● petrochemical industry, chemical systems with corrosive and abrasive liquids

● Heat treatment facilities of steel mills

Maintenance and precautions for well submersible pumps:

In order to ensure the normal operation of the submersible pump unit for wells, reduce the failure rate and prolong the service life, it is necessary to strengthen the maintenance and repair of the deep well submersible pump, and regularly carry out comprehensive maintenance on the submersible pump and its control system, at least once a year. Preventive maintenance.

The maintenance and maintenance methods that need to be paid attention to when using the submersible pump are as follows:

1. The environment in which the deep well pump unit is used should be kept dry. The surface of the vertical motor should be kept clean, and the air inlet should not be obstructed by dust, fibers and other debris, ensuring unimpeded air passage. Heat sources should not be placed around the motor, and should not be used outdoors under direct sunlight to avoid damage caused by overheating during operation.

2. When the deep well pump device is running, always pay attention to the readings of the relevant instruments, and regularly record the relevant parameters (such as the voltage of the motor,

3. If any abnormal sound is found during operation, stop immediately for inspection. If the anti-reverse device of the motor is found to be ineffective, it must be repaired to clear the dirt so that it can work well.

4. When the overcurrent protection or short circuit protection of the motor control device continuously occurs, it should be checked whether the fault is from the motor overload or the protection device is too low. If the setting value of the protection device is too low, the setting value of the protection device should be adjusted to a reasonable value; if it is caused by the overload of the motor, the cause of the motor overload should be checked in time, and the overload fault can be eliminated before it can be put back into operation.

5. When parking for any reason, please pay attention to check the oil level of the motor oil standard. If the oil level is lower than half of the oil standard, the new oil should be replenished in time to ensure the reliable lubrication of the angular contact ball bearing of the motor.

Stainless steel hot spring pump

Long shaft deep well pump

Stainless steel deep well pump

Submersible electric pump

位于Schw?bischGmünd的凱森Kaysen泵業有限公司是 *的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持 各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。

凱森始終堅持“重質量，講信譽”為宗旨。產品現 全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。

The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.