|
- 品牌：德國KAYSEN
- 貨號：KS5889569
- 發布日期： 2019-10-11
- 更新日期： 2024-10-21
| 外型尺寸 | |
| 貨號 | KS5889569 |
| 品牌 | KAYSEN |
| 用途 | 抽水、化工、制藥、石油、冶金、染料、冶煉、電力、電鍍、農藥、造紙、食品、紡織等行業酸洗工藝、制酸制堿、噴漆工藝、有色金屬冶煉中的電解液輸送、離子膜項目中的氯水輸送、廢水處理、電鍍、農藥領域。 |
| 型號 | KAYSEN |
| 工作壓差 | 0 |
| 壓力環境 | 常壓 |
| 介質溫度 | 250℃ |
| 驅動方式 | 電動 |
| 適用介質 | 水 |
長軸深井泵-深井泵-KAYSEN泵業
GERMANY KAYSEN PUMP CO .,LTD
長軸深井泵多數是一個立式單吸多級離心泵，其葉輪裝在井中動水位以下，動力機設置在井上，通過傳動長軸驅動葉輪在導流殼內旋轉，水流沿導流殼與葉輪之間的流道，經輸水管向上提升到地面。該泵使用壽命和檢修期較長，使用范圍廣泛，而且能夠在較惡劣的環境中使用，檢修也極為方便。
主要特點：
●采用護管可靠地保護了傳動部件和潤滑部件
采用護管結構，使輸送介質在護管外流動，不與傳動部件和潤滑部件接觸，不因泵輸送介質中含有泥砂、氧化鐵皮、油污等異物，而影響泵的傳動部件和潤滑部件工作。
●特殊的潤滑方式和軸承結構保證了泵長期穩定運行
泵的軸承除采用常規的橡膠導軸承外，還根據特殊需要，采用了石墨軸承、硬質合金軸承，提高泵的耐磨耐溫的使用性能。
泵的潤滑方式根據使用環境條件不同，可選用2~3kg/cm2的自來水（清潔水）潤滑泵下軸承。在無自來水（清潔水）的特殊環境中，泵采用了自潤滑方式：一種是使用鈣基潤滑脂潤滑，此潤滑方式完全采用了國外先進技術，泵無論在哪種特殊環境中，均可正常長期使用。另一種潤滑方式是泵輸送介質較清潔時，采用泵體內輸送介質進行自潤滑。
●使用高強度材質，泵具有良好的穩定性
泵的葉輪和軸采用了耐磨高強度不銹鋼材質，揚水管及護管采用了無縫鋼管或不銹鋼管，強度高，穩定性好。
●泵能在特殊的惡劣環境中長期正常運行
●泵結構緊湊，安裝調試及維護方便
主要應用：
長軸深井泵運行注意事項：
1、每臺班次必須檢查泵體螺栓。
2、檢查長軸深井泵填料是否有過大漏水現象，如有漏水及時添加盤根或全部更換。（長軸深井泵進行正常狀態）
3、高速電機在運行中容易發熱。當用手觸摸電機端蓋，如短時間感覺太燙，不能觸摸，該機應停止運行。進行冷卻，更換另一臺機運行。
4、電機在運行中如發出“骨碌骨碌”聲，表示軸承缺油，必須加油；如發出“梗?！甭暎硎据S承內外鋼圈或滾珠破損，應停機更換。更多內容：LC型立式長軸泵。
5、運行中突然停機或自動停機后，電機發生“嗡嗡”聲，這是可能是電源缺相或主回路沒有完全斷開，應立即拉閘（總閘也可），否則會燒毀電機和設備。停機后必須查明原因，排除故障后再啟動運行。
6、運行中水壓表指針下跌，或水壓表指針上不去。（不足8kg）這時可能進水管和水泵內有空氣。如發現進水管中的橡皮短管有下陷現象，確定進水管濾網被堵塞，應立即停機消除濾網上雜務后再啟動運行。
7、注意窨井污水，水位過高，必須啟動排污泵排除。（及時停泵）
8、做好運行機械及儀表讀數記錄，并監視其變動，如電流表讀數過高。必須停機查找原因，排除故障后再啟動運行。
9、操作空氣開關和檢查配電柜時，應注意安全，避免觸電。（*停電檢查）
10、運行中的機械，切勿進行檢修。如需維修，須先停機，并掛警示牌。
11、吃飯離崗前，啟動運行的機械。必須注意觀察水壓、電壓、電流及機械運行的狀況。確實無異常時，方可離開。（在半小時以內）更多內容：TDLC型長軸泵。
12、水泵廠值班人員必須做到，上班不遲到，下班不早退，中途不離崗，有事先請假。
13、自動運行檔位如果不能啟動運行或運行數分鐘后停機，則可能是自動訊號線路接觸不良。必須停機檢修（如修理后不到，改用手動按鈕運行，同時要更換自動線路配件。）
14、水泵的聯軸器的橡皮圈，必須每臺班次檢查一下，發現問題及更換。
15、水泵廠值班人員和維修人員的安全：必須做到手上沒有水和潮氣，才能操作電器開關。 為了確保水泵房的安全運行，按時供水，水泵廠值班人員上崗，必須安全操作。特制定本安全操作規程。
The long-axis deep well pump is mostly a vertical single-suction multi-stage centrifugal pump. The impeller is installed below the moving water level in the well. The power machine is placed on the well. The impeller is driven by the long shaft to rotate in the diversion shell. The water flows along the diversion shell and the impeller. The flow path between them is lifted up to the ground via the water pipe. The pump has a long service life and maintenance period, is widely used, and can be used in harsh environments, and is also extremely convenient for maintenance.
main feature:
●The transmission parts and lubrication parts are reliably protected by the protective tube
The protective tube structure is adopted to make the conveying medium flow outside the protective tube, and is not in contact with the transmission component and the lubricating component, and does not affect the transmission component and the lubricating component of the pump due to the foreign matter contained in the pump conveying medium containing mud sand, iron oxide scale and oil stain.
●Special lubrication method and bearing structure ensure long-term stable operation of the pump
In addition to the conventional rubber guide bearing, the pump bearing also uses graphite bearings and hard alloy bearings according to special needs to improve the wear resistance and temperature resistance of the pump.
The lubrication method of the pump can be used to lubricate the lower bearing of the pump with 2~3kg/cm2 tap water (clean water) depending on the environmental conditions. In the special environment without running water (clean water), the pump adopts self-lubricating method: one is lubricated with calcium-based grease, which is completely advanced technology. The pump can be used in any special environment. Normal long-term use. Another way of lubrication is to use the pump to transport the medium for self-lubrication when the pump is clean.
●Use high strength material, pump has good stability
The impeller and shaft of the pump are made of wear-resistant high-strength stainless steel. The pipe and the protective pipe are made of seamless steel pipe or stainless steel pipe with high strength and good stability.
●The pump can operate normally for a long time in a special harsh environment
●The pump is compact, easy to install, debug and maintain.
main application:
Long-axis deep well pump operation notes:
1. The pump body bolts must be checked for each shift.
2. Check whether the long shaft deep well pump packing has excessive water leakage. If there is water leakage, add packing or replace it all. (Long shaft deep well pump is in normal state)
3. High-speed motors are prone to heat during operation. When the motor end cover is touched by hand, if it feels too hot for a short time and cannot be touched, the machine should stop running. Cool down and replace another machine.
4. If the motor is in operation, it will sound “bone and bones”, indicating that the bearing is short of oil and must be refueled; if the sound of “stalk” is issued, it means that the inner and outer steel rings or balls are damaged, and should be replaced by stop. More: LC type vertical long axis pump.
5. After a sudden stop or automatic shutdown during operation, the motor will “beep”. This may be due to the lack of phase of the power supply or the main circuit is not completely disconnected. It should be pulled immediately (the main gate is also available), otherwise the motor will be burned and device. After the machine is stopped, the cause must be ascertained, and the operation should be started after the fault is eliminated.
6. The pointer of the water pressure gauge falls during operation, or the pointer of the water pressure gauge does not go. (less than 8kg) At this time, there may be air in the inlet pipe and the pump. If it is found that the rubber short pipe in the inlet pipe has a subsidence phenomenon, it is determined that the inlet pipe filter is blocked, and the machine should be stopped immediately to eliminate the chores on the filter network before starting the operation.
7, pay attention to the sewage well, the water level is too high, must start the sewage pump to eliminate. (stop pump in time)
8. Record the operating machinery and instrument readings and monitor their changes, such as the current meter reading is too high. You must stop the machine to find the cause, and then start the operation after troubleshooting.
9. When operating the air switch and checking the power distribution cabinet, pay attention to safety and avoid electric shock. (preferably power outage check)
10. Do not perform maintenance on the running machine. If maintenance is required, stop the machine first and hang the warning sign.
11. Start the running machinery before eating out of the post. Care must be taken to observe the conditions of water pressure, voltage, current and mechanical operation. If there is no abnormality, you can leave. (Within half an hour) More: TDLC long shaft pump.
12. The staff of the pump factory must do it. They are not late for work, do not leave early after work, do not leave the job in the middle, and have a leave in advance.
13. If the automatic running gear position cannot be started or stopped after a few minutes of running, the automatic signal line may be in poor contact. Must be shut down for maintenance (if not after repair, use the manual button to operate, and replace the automatic line accessories.)
14. The rubber band of the coupling of the pump must be checked every shift, and the problem is found and replaced.
15. Safety of the duty and maintenance personnel of the pump factory: It is necessary to operate the electrical switch without water and moisture on the hand. In order to ensure the safe operation of the pump house, water supply on time, the water pump factory on duty, must be safe to operate. This safety operation procedure is specially formulated.
Stainless steel hot spring pump
Long shaft deep well pump
Stainless steel deep well pump
Submersible electric pump
位于Schw?bischGmünd的凱森Kaysen泵業有限公司是世界*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持世界各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。
凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
